Panorama Score Clock


ON - - - - OFF	20:00.0 30 DN

HORN	MISC. SHOT TIME	CLOCK MODES	SET	7	8	9	YES
TIME OUT TIMER	PNLTY ON OFF	PNLTY INSERT	TIME	4	5	6	NO
HOME GOAL	HOME SHOTS	PNLTY CLEAR	HOME PNLTY	1	2	3	HOME SCORE
GUEST GOAL	GUEST SHOTS	PNLTY EDIT	GUEST PNLTY	:	BLANK	0	GUEST SCORE

Starting Up

NOTE: Before starting, the 30 second shot cable (and the set of goal pegs) must be picked up at the Panorama front desk.

Ensure that the power switch (right side, near the back of the console) is in the "off" position.
Toggle the running time switch ON
- - - -
OFF to the "off" position.
Ensure that the 30 second cable is attached (left side panel, near the front of the console).
Toggle the console's power switch to the "on" position.
Receive the console message...

DO YOU WANT TO START WHERE TURNED OFF LAST? PRESS 'YES' OR 'NO'
Enter
NO
Receive the promotional message...

...blah.blah..I AM...blah.blah...
Enter
0
Receive the console message...

MODEL: 0 # # - # # # #
Continue entering the console's model number...

0
8
3
2
6
1
Receive the console message...

USE SHOT CLOCKS? PRESS 'YES' OR 'NO'
Enter
YES
Receive the console message...

SHOT TIME ##
Enter
3
0
Receive the console message...

O.B. TIME ##
Enter
3
0
Receive the console message...

USE PENALTY TIME OUT? PRESS 'YES' OR 'NO'
Enter
YES
Receive the console message...

0:00.0 30 DN
Check that the wall scoreboard display matches the console display.
Check that the wall shot clocks both display "30".

NOTE: If anything goes wrong, then start over. If problems persist, then have the front desk call a maintenance person.

Setting Time and Period

NOTE: Unless instructed otherwise by the referees, all periods shall be 20 minutes in duration and all warmups and intermissions shall be 5 minutes in duration.

Toggle the running time switch ON
- - - -
OFF to the "off" position.
Set the time (e.g.
SET
TIME
5
:
YES for a warmup).
Receive the console message...

PERIOD x
(where "x" corresponds to whatever period is currently displayed on the wall scoreboard).
Set the period (e.g.
1 ).
Receive the console message...

5:00.0 30 DN

NOTE: The period number can only be set when the time is set.

Timing a Period

Ensure that the period time and number have been set properly.
Ensure that the 30 second clocks are reset to "30".
Ensure that the penalty time is set appropriately...
1. If no penalties currently in effect...
  Ensure that penalty time is "off" by entering PNLTY
  ON
  OFF
  and receiving the console message...
  
  TIME OFF
2. OR if penalties are carrying over from previous period...
  Ensure that penalty time is "on" by entering PNLTY
  ON
  OFF
  and receiving the console message...
  
  TIME ON
As soon as the referee whistles play to start,
toggle the running time switch ON
- - - -
OFF to the "on" position.
When the clock counts down to zero, the horn will sound (and continue to sound) until the running time switch is toggled ON
- - - -
OFF to the "off" position.

NOTE: Unless instructed otherwise by the referees, all periods should be straight running time except for the last five minutes of the third period and there are five or fewer goals separating the two teams. This means that the only time the clock is stopped is

for a referee timeout (due to injury, equipment problem, team timeout, etc.)
during a play stoppage in the last five minutes of a close game.

Timing an Intermission

Ensure that the intermission time has been set properly.
Ensure that the 30 second shot clocks have been disabled by entering
SET MISC.
SHOT
CLOCK
BLANK.
Ensure that the penalty time is "off" by entering PNLTY
ON
OFF
and receiving the console message...

TIME OFF
Toggle the running time switch ON
- - - -
OFF to the "on" position.
When the clock counts down to zero, the horn will sound (and continue to sound) until the running time switch is toggled ON
- - - -
OFF to the "off" position.

Keeping Score

To set the home (or guest) score...
enter
SET HOME
SCORE
0 (or
SET GUEST
SCORE
0 )
and receive the console message...
HOME 0
To increment the guest (or home) score...
enter GUEST
SCORE
1 (or HOME
SCORE
1 )
and receive the console message...
GUEST x +1 (where "x" corresponds to whatever guest score is currently displayed on the wall scoreboard).
To correct a score, see 1.

Keeping Penalties

To set an initial home (or guest) penalty (i.e. when both penalty boxes are empty)...
1. Ensure that the penalty time is "off" by entering PNLTY
  ON
  OFF
  and receiving the console message...
  
  TIME OFF
2. Enter
  SET HOME
  PNLTY (or
  SET GUEST
  PNLTY )
3. Enter the duration of the penalty...
  (e.g.
  2
  : for a two minute minor )
4. Receive the console message...
  
  PNLTY 2:00 (Y - N)
5. Enter
  YES to confirm the information, or
  NO to start over.
6. Enter a two digit player number...
  (e.g.
  1
  1 )
7. As soon as the referee whistles play to restart,
  press PNLTY
  ON
  OFF and receive the console message...
  
  TIME ON
To set a subsequent penalty (i.e. when one or more penalties are all ready being served)......
1. Enter
  SET HOME
  PNLTY (or
  SET GUEST
  PNLTY )
2. Enter the duration of the penalty...
  (e.g.
  2
  : for a two minute minor )
3. Receive the console message...
  
  PNLTY 2:00 (Y - N)
4. Enter
  YES to confirm the information, or
  NO to start over.
5. Wait!
6. As soon as the referee whistles play to restart,
  enter another two digit player number...
  (e.g.
  2
  2 )
To clear a home (or guest) penalty...
1. Enter HOME
  PNLTY (or GUEST
  PNLTY ) until the appropriate penalty displays on the console. For example...
  H2 1:23 22
2. Enter PNLTY
  CLEAR
3. Receive the console message...
  
  CLEAR (Y - N)
4. Enter
  YES to confirm the penalty clear, or
  NO to start over.